PASA00ESP Site Information Form (site log v2.0)
International GNSS Service
See Instructions at:
https://files.igs.org/pub/station/general/sitelog_instr_v2.0.txt
0. Form
Prepared by (full name) : ARANZADI (geodesia@aranzadi.eus)
Date Prepared : 2024-04-18
Report Type : UPDATE
If Update:
Previous Site Log : pasa00esp_20231031.log
Modified/Added Sections : 3.31, 3.32
1. Site Identification of the GNSS Monument
Site Name : Pasaia
Nine Character ID : PASA00ESP
Monument Inscription :
IERS DOMES Number : 19351S001
CDP Number : (A4)
Monument Description : STEEL MAST
Height of the Monument : 1.7 m
Monument Foundation : MAST SCREW ANCHORED TO BUILDING WALL
Foundation Depth : (m)
Marker Description : (CHISELLED CROSS/DIVOT/BRASS NAIL/etc)
Date Installed : 2007-02-12
Geologic Characteristic : (BEDROCK/CLAY/CONGLOMERATE/GRAVEL/SAND/etc)
Bedrock Type : (IGNEOUS/METAMORPHIC/SEDIMENTARY)
Bedrock Condition : (FRESH/JOINTED/WEATHERED)
Fracture Spacing : (0 cm/1-10 cm/11-50 cm/51-200 cm/over 200 cm)
Fault zones nearby : NO
Distance/activity : (multiple lines)
Additional Information : The monument is on the roof of the
: AZTI-Tecnalia centre of Pasaia
: Antenna is approximately 15m above ground level
2. Site Location Information
City or Town : Pasaia
State or Province : Gipuzkoa
Country or Region : ESP
Tectonic Plate : EURASIAN
Approximate Position (ITRF)
X coordinate (m) : 4644909.237
Y coordinate (m) : -156645.166
Z coordinate (m) : 4353622.778
Latitude (N is +) : +431918.35
Longitude (E is +) : -0015553.45
Elevation (m,ellips.) : 67.3
Additional Information : Permanent GNSS and Tide Gauge
3. GNSS Receiver Information
3.1 Receiver Type : LEICA GRX1200PRO
Satellite System : GPS
Serial Number : 455999
Firmware Version : 3.00/2.121
Elevation Cutoff Setting : 0 deg
Date Installed : 2007-02-12
Date Removed : 2007-07-20
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.2 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS
Serial Number : 350102
Firmware Version : 5.10/3013
Elevation Cutoff Setting : 0 deg
Date Installed : 2007-07-20
Date Removed : 2007-09-05
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.3 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 5.50/3.014
Elevation Cutoff Setting : 0 deg
Date Installed : 2007-09-05
Date Removed : 2008-11-17
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.4 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 6.02/3.014
Elevation Cutoff Setting : 0 deg
Date Installed : 2008-11-17
Date Removed : 2009-03-26
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.5 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 7.02/3.016
Elevation Cutoff Setting : 0 deg
Date Installed : 2009-03-26
Date Removed : 2009-06-10
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.6 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 7.02/3.017
Elevation Cutoff Setting : 0 deg
Date Installed : 2009-06-10
Date Removed : 2010-03-11
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.7 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 7.80/3.018
Elevation Cutoff Setting : 0 deg
Date Installed : 2010-03-11
Date Removed : 2010-05-03
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.8 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 7.80/3.019
Elevation Cutoff Setting : 0 deg
Date Installed : 2010-05-03
Date Removed : 2010-07-07
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.9 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 8.00/3.019
Elevation Cutoff Setting : 0 deg
Date Installed : 2010-07-07
Date Removed : 2011-05-16
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.10 Receiver Type : LEICA GRX1200GGPRO
Satellite System : GPS+GLO
Serial Number : 455999
Firmware Version : 8.20/3.019
Elevation Cutoff Setting : 0 deg
Date Installed : 2011-05-16
Date Removed : 2011-06-06
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.11 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 1.10/4.007
Elevation Cutoff Setting : 0 deg
Date Installed : 2011-06-06
Date Removed : 2012-01-27
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.12 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 2.0/4.007
Elevation Cutoff Setting : 0 deg
Date Installed : 2012-02-27
Date Removed : 2012-05-07
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.13 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 2.5/6.110
Elevation Cutoff Setting : 0 deg
Date Installed : 2012-05-07
Date Removed : 2012-08-28
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.14 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 2.62/6.112
Elevation Cutoff Setting : 0 deg
Date Installed : 2012-08-28
Date Removed : 2013-04-25
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.15 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 3.00/6.113
Elevation Cutoff Setting : 0 deg
Date Installed : 2013-04-25
Date Removed : 2014-04-01
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.16 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 3.00/6.113
Elevation Cutoff Setting : 0 deg
Date Installed : 2014-04-01
Date Removed : 2014-05-23
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : GR10 receiver connected to ALDCBS1X2
: signal splitter.
: The 2nd output of the splitter is connected
: with the receiver of station PAS2.
3.17 Receiver Type : LEICA GR10
Satellite System : GPS+GLO
Serial Number : 1700316
Firmware Version : 3.03/6.214
Elevation Cutoff Setting : 0 deg
Date Installed : 2014-05-23
Date Removed : 2015-03-06
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : GR10 receiver connected to ALDCBS1X2
: signal splitter.
3.18 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 3.11/6.403
Elevation Cutoff Setting : 0 deg
Date Installed : 2015-03-06
Date Removed : 2015-09-04T14:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : GR10 receiver connected to ALDCBS1X2
: signal splitter.
3.19 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 3.21/6.403
Elevation Cutoff Setting : 0 deg
Date Installed : 2015-09-04T14:00Z
Date Removed : 2015-11-03T11:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.20 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 3.22/6.521
Elevation Cutoff Setting : 0 deg
Date Installed : 2015-11-03T11:00Z
Date Removed : 2016-03-16T15:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.21 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 3.22/6.522
Elevation Cutoff Setting : 0 deg
Date Installed : 2016-03-16T15:00Z
Date Removed : 2016-06-06T10:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.22 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.00/6.522
Elevation Cutoff Setting : 0 deg
Date Installed : 2016-06-06T10:00Z
Date Removed : 2016-11-11T13:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.23 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.02/6.522
Elevation Cutoff Setting : 0 deg
Date Installed : 2016-11-11T13:00Z
Date Removed : 2017-02-27T07:56Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.24 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.11/6.523
Elevation Cutoff Setting : 0 deg
Date Installed : 2017-02-27T07:56Z
Date Removed : 2018-03-13T09:25Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Firmware updated
3.25 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.20/6.524
Elevation Cutoff Setting : 0 deg
Date Installed : 2018-03-13T09:25Z
Date Removed : 2019-04-23T10:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.26 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+SBAS
Serial Number : 1700316
Firmware Version : 4.20/6.525
Elevation Cutoff Setting : 0 deg
Date Installed : 2019-04-23T10:00Z
Date Removed : 2019-04-24T09:20Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.27 Receiver Type : LEICA GR10
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.20/6.525
Elevation Cutoff Setting : 0 deg
Date Installed : 2019-04-24T09:20Z
Date Removed : 2019-06-17T05:55Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.28 Receiver Type : LEICA GR30
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1703003
Firmware Version : 4.31/7.403
Elevation Cutoff Setting : 0 deg
Date Installed : 2019-06-17T05:55Z
Date Removed : 2019-12-02T09:38Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : New receiver installed
3.29 Receiver Type : LEICA GR30
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.31/7.403
Elevation Cutoff Setting : 0 deg
Date Installed : 2019-12-02T09:38Z
Date Removed : 2022-02-02T10:20Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : Former GR10 receiver upgraded to GR30.
3.30 Receiver Type : LEICA GR30
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.52/7.711
Elevation Cutoff Setting : 0 deg
Date Installed : 2022-02-02T10:20Z
Date Removed : 2023-10-27T12:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : FW updated
3.31 Receiver Type : LEICA GR30
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.70/7.813
Elevation Cutoff Setting : 0 deg
Date Installed : 2023-10-27T12:00Z
Date Removed : 2024-04-18T15:00Z
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : (multiple lines)
3.32 Receiver Type : LEICA GR30
Satellite System : GPS+GLO+GAL+BDS+SBAS
Serial Number : 1700316
Firmware Version : 4.80/7.900
Elevation Cutoff Setting : 0 deg
Date Installed : 2024-04-18T15:00Z
Date Removed : CCYY-MM-DDThh:mmZ
Temperature Stabiliz. : (deg C) +/- (deg C)
Additional Information : FW update
3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions)
Satellite System : (GPS+GLO+GAL+BDS+QZSS+IRNSS+SBAS)
Serial Number : (A20, but note the first A5 is used in SINEX)
Firmware Version : (A11)
Elevation Cutoff Setting : (deg)
Date Installed : (CCYY-MM-DDThh:mmZ)
Date Removed : (CCYY-MM-DDThh:mmZ)
Temperature Stabiliz. : (none or tolerance in degrees C)
Additional Information : (multiple lines)
4. GNSS Antenna Information
4.1 Antenna Type : LEIAT504 LEIS
Serial Number : 102852
Antenna Reference Point : BPA
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIS
Radome Serial Number : Unknown
Antenna Cable Type : Leica
Antenna Cable Length : 30 m
Date Installed : 2007-02-12
Date Removed : 2007-07-20
Additional Information : (multiple lines)
4.2 Antenna Type : LEIAT504 LEIS
Serial Number : n/a
Antenna Reference Point : BPA
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIS
Radome Serial Number : Unknown
Antenna Cable Type : Leica
Antenna Cable Length : 30 m
Date Installed : 2007-07-20
Date Removed : 2007-09-05
Additional Information : (multiple lines)
4.3 Antenna Type : LEIAT504GG LEIS
Serial Number : 102852
Antenna Reference Point : BPA
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIS
Radome Serial Number : Unknown
Antenna Cable Type : Leica
Antenna Cable Length : 30 m
Date Installed : 2007-09-05
Date Removed : 2011-06-06
Additional Information : (multiple lines)
4.4 Antenna Type : LEIAR25.R4 LEIT
Serial Number : 10351001
Antenna Reference Point : BPA
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIT
Radome Serial Number : Unknown
Antenna Cable Type : Leica
Antenna Cable Length : 30 m
Date Installed : 2011-06-06
Date Removed : 2013-12-17
Additional Information : SECO Leveling Mount added
4.5 Antenna Type : LEIAR20 LEIM
Serial Number : 16073034
Antenna Reference Point : BAM
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIM
Radome Serial Number : Unknown
Antenna Cable Type : Leica+Splitter
Antenna Cable Length : 30 m
Date Installed : 2013-12-17
Date Removed : 2014-07-11
Additional Information : SECO Leveling Mount
4.6 Antenna Type : LEIAR20 LEIM
Serial Number : 16073034
Antenna Reference Point : BAM
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIM
Radome Serial Number : Unknown
Antenna Cable Type : Leica+Splitter
Antenna Cable Length : 30 m
Date Installed : 2014-07-11
Date Removed : 2014-10-20
Additional Information : SECO Leveling Mount
: A 0.6x0.6 m^2 metal shield was
: installed with Eccosorb ANW-77 on top. The
: spacing between the BPA and the top of the
: Eccosorb is 8.6 cm
4.7 Antenna Type : LEIAT504GG LEIS
Serial Number : 102842
Antenna Reference Point : BPA
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIS
Radome Serial Number : Unknown
Antenna Cable Type : Leica+Splitter
Antenna Cable Length : 30 m
Date Installed : 2014-10-20
Date Removed : 2014-12-05
Additional Information : SECO Leveling Mount
: A 0.6x0.6 m^2 metal shield was
: installed with Eccosorb ANW-77 on top. The
: spacing between the BPA and the top of the
: Eccosorb is 8.6 cm
4.8 Antenna Type : LEIAR20 LEIM
Serial Number : 16073034
Antenna Reference Point : BAM
Marker->ARP Up Ecc. (m) : 0.0000
Marker->ARP North Ecc(m) : 0.0000
Marker->ARP East Ecc(m) : 0.0000
Alignment from True N : 0 deg
Antenna Radome Type : LEIM
Radome Serial Number : Unknown
Antenna Cable Type : Leica+Splitter
Antenna Cable Length : 30 m
Date Installed : 2014-12-05
Date Removed : CCYY-MM-DDThh:mmZ
Additional Information : SECO Leveling Mount
: A 0.6x0.6 m^2 metal shield was
: installed with Eccosorb ANW-77 on top. The
: spacing between the BPA and the top of the
: Eccosorb is 8.6 cm
4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions)
Serial Number : (A*, but note the first A5 is used in SINEX)
Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.)
Marker->ARP Up Ecc. (m) : (F8.4)
Marker->ARP North Ecc(m) : (F8.4)
Marker->ARP East Ecc(m) : (F8.4)
Alignment from True N : (deg; + is clockwise/east)
Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions)
Radome Serial Number :
Antenna Cable Type : (vendor & type number)
Antenna Cable Length : (m)
Date Installed : (CCYY-MM-DDThh:mmZ)
Date Removed : (CCYY-MM-DDThh:mmZ)
Additional Information : (multiple lines)
5. Surveyed Local Ties
5.x Tied Marker Name :
Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc)
Tied Marker CDP Number : (A4)
Tied Marker DOMES Number : (A9)
Differential Components from GNSS Marker to the tied monument (ITRS)
dx (m) : (m)
dy (m) : (m)
dz (m) : (m)
Accuracy (mm) : (mm)
Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc)
Date Measured : (CCYY-MM-DDThh:mmZ)
Additional Information : (multiple lines)
6. Frequency Standard
6.1 Standard Type : INTERNAL
Input Frequency : (if external)
Effective Dates : 2007-02-12/CCYY-MM-DD
Notes : (multiple lines)
6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc)
Input Frequency : (if external)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
7. Collocation Information
7.1 Instrumentation Type : TIDE GAUGE
Status : PERMANENT
Effective Dates : 2007-02-19/CCYY-MM-DD
Notes : Paroscientific Series 8000 Gauge
7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc)
Status : (PERMANENT/MOBILE)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
8. Meteorological Instrumentation
8.1.1 Humidity Sensor Model : MET3A
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ107250
Data Sampling Interval : 600 sec
Accuracy (% rel h) : 2 % rel h
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2009-03-04/2011-04-08
Notes : (multiple lines)
8.1.2 Humidity Sensor Model : MET3
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ 96233
Data Sampling Interval : 600 sec
Accuracy (% rel h) : 2 % rel h
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2011-06-06/2019-12-12
Notes : (multiple lines)
8.1.3 Humidity Sensor Model : Vaisala WXT520
Manufacturer : Vaisala
Serial Number : R2230367
Data Sampling Interval : 600 sec
Accuracy (% rel h) : (% rel h)
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2019-12-12/CCYY-MM-DD
Notes : (multiple lines)
8.1.x Humidity Sensor Model :
Manufacturer :
Serial Number :
Data Sampling Interval : (sec)
Accuracy (% rel h) : (% rel h)
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : (m)
Calibration date : (CCYY-MM-DD)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
8.2.1 Pressure Sensor Model : MET3A
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ107250
Data Sampling Interval : 600 sec
Accuracy : 0.08 hPa
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2009-03-04/2011-04-08
Notes : (multiple lines)
8.2.2 Pressure Sensor Model : MET3
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ 96233
Data Sampling Interval : 600 sec
Accuracy : 0.08 hPa
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2011-06-06/2019-12-12
Notes : (multiple lines)
8.2.3 Pressure Sensor Model : Vaisala WXT520
Manufacturer : Vaisala
Serial Number : R2230367
Data Sampling Interval : 600 sec
Accuracy : (hPa)
Height Diff to Ant : -1 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2019-12-12/CCYY-MM-DD
Notes : (multiple lines)
8.2.x Pressure Sensor Model :
Manufacturer :
Serial Number :
Data Sampling Interval : (sec)
Accuracy : (hPa)
Height Diff to Ant : (m)
Calibration date : (CCYY-MM-DD)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
8.3.1 Temp. Sensor Model : MET3A
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ107250
Data Sampling Interval : 600 sec
Accuracy : 0.5 deg C
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2009-03-04/2011-04-08
Notes : (multiple lines)
8.3.2 Temp. Sensor Model : MET3
Manufacturer : PAROSCIENTIFIC
Serial Number : DQ 96233
Data Sampling Interval : 600 sec
Accuracy : 0.5 deg C
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1.5 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2011-06-06/2019-12-12
Notes : (multiple lines)
8.3.3 Temp. Sensor Model : Vaisala WXT520
Manufacturer : Vaisala
Serial Number : R2230367
Data Sampling Interval : 600 sec
Accuracy : (deg C)
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : -1 m
Calibration date : (CCYY-MM-DD)
Effective Dates : 2019-12-12/CCYY-MM-DD
Notes : (multiple lines)
8.3.x Temp. Sensor Model :
Manufacturer :
Serial Number :
Data Sampling Interval : (sec)
Accuracy : (deg C)
Aspiration : (UNASPIRATED/NATURAL/FAN/etc)
Height Diff to Ant : (m)
Calibration date : (CCYY-MM-DD)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
8.4.x Water Vapor Radiometer :
Manufacturer :
Serial Number :
Distance to Antenna : (m)
Height Diff to Ant : (m)
Calibration date : (CCYY-MM-DD)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Notes : (multiple lines)
8.5.x Other Instrumentation : (multiple lines)
9. Local Ongoing Conditions Possibly Affecting Computed Position
9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc)
Observed Degradations : (SN RATIO/DATA GAPS/etc)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Additional Information : (multiple lines)
9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Additional Information : (multiple lines)
9.3.x Signal Obstructions : (TREES/BUILDINGS/etc)
Effective Dates : (CCYY-MM-DD/CCYY-MM-DD)
Additional Information : (multiple lines)
10. Local Episodic Effects Possibly Affecting Data Quality
10.1 Date : 2014-04-01/CCYY-MM-DD
Event : Added TPS NET-G3A receiver,ALDCBS1X2 amplified
: signalsplitter to original antennaconnection. No
: change tooriginal antenna.GR10 powers the
: antenna and the splitter.
10.x Date : (CCYY-MM-DD/CCYY-MM-DD)
Event : (TREE CLEARING/CONSTRUCTION/etc)
11. On-Site, Point of Contact Agency Information
Agency : ARANZADI Society of Sciences
: Department of Applied Geodesy
Preferred Abbreviation : ARA
Mailing Address : Zorroagagaina 11
: 20018 SAN SEBASTIÁN
: Spain
Primary Contact
Contact Name : ARANZADI
Telephone (primary) :
Telephone (secondary) :
Fax :
E-mail : geodesia@aranzadi.eus
Secondary Contact
Contact Name : Mr. Aitor Aginaga
Telephone (primary) : +34 943 46 61 42
Telephone (secondary) :
Fax :
E-mail : aitoraguinaga@gmail.com
Additional Information : (multiple lines)
12. Responsible Agency (if different from 11.)
Agency : Gipuzkoako Foru Aldundia - Diputación Foral de
: Gipuzkoa
: Department of Mobility and Planning
Preferred Abbreviation : GFA
Mailing Address : Plaza Julio Caro Baroja 2
: 20.018 Donostia - San Sebastián
: Spain
Primary Contact
Contact Name : GFA GNSS
Telephone (primary) :
Telephone (secondary) :
Fax :
E-mail : liz@gipuzkoa.eus
Secondary Contact
Contact Name : Mikelo Elorza
Telephone (primary) :
Telephone (secondary) :
Fax :
E-mail : melorza@gipuzkoa.net
Additional Information : (multiple lines)
13. More Information
Primary Data Center : BKG
Secondary Data Center :
URL for More Information : http://b5m.gipuzkoa.net/web5000/en/geodesy/
Hardcopy on File
Site Map : (Y or URL)
Site Diagram : (Y or URL)
Horizon Mask : (Y or URL)
Monument Description : (Y or URL)
Site Pictures : (Y or URL)
Additional Information : (multiple lines)
Antenna Graphics with Dimensions
LEIAT504
+-------+ <-- 0.1393
/ + \ <-- 0.1282 L2
| + | <-- 0.1093 L1
+-----------------+-------------+------------------+ <-- 0.1020 TCR
| |
| |
| |
| |
+-+--------------------------------------------------+-+ <-- 0.0380
+-------------------+-------------+--------------------+ <-- 0.1020 BCR
| |
| |
+------x------+ <-- 0.0000 BPA=ARP
<-- 0.3794 -->
LEIAT504GG
+-------+ <-- 0.1393
/ \
| |
+-----------------+-------------+-----------------+ <-- 0.1012 TCR
| |
| |
| |
| |
+-+-------------------------------------------------+-+ <-- 0.0378
+-------------------+-------------+-------------------+ <-- 0.0345 BCR
| |
| |
+------x------+ <-- 0.0000 BPA=ARP
<-- 0.3794 -->
LEIAR25.R4
+-------+ <-- 0.1995
/ \
+---+-------------+---+ <-- 0.1606 TCR
| |
|---------------------------|
|---------------------------------|
|---------------------------------------|
+---------------------------------------------+
| |
| |
+-+---------------------------------------------+-+
+-----------------+-------------+-----------------+ <-- 0.0320 BCR
| |
| |
+------x------+ <-- 0.0000 BPA=ARP
(5/8' thread might
differ from BPA!)
<-- 0.3802 -->
LEIAR20
+-----+ <-- 0.1613
/ \
| |
+----------------+-----------+----------------+ <-- 0.1113 TCR
| |
| |
| |
| |
+-+---------------------------------------------+-+
+------------------+-----------+------------------+ <-- 0.0323 BCR
| |
| |
+-----x-----+ <-- 0.0013 BPA
+-+ <-- 0.0000 BAM=ARP
<-- 0.3200 -->
ARP: Antenna Reference Point
L1 : L1 Phase Center L2 : L2 Phase Center
TCR: Top of Chokering BCR: Bottom of Chokering
BPA: Bottom of Preamplifier
